Intertek Labtest CONTROL, COPY Standard No.: (S0_ 23-1 Version: Y Copy No.: ol ol Huime Lu Distributeto:- Standard Intertek Testing Services Limited., Shanghai TFH Division ISO INTERNATIONAL STANDARD 2380-1 CONTROL, COPY Third edition 2004-12-15 Assemblytoolsforscrewsandnuts- Screwdriversforslotted-head screws Part 1: Tips for hand- and machine-operated screwdrivers Outils de manceuvre pour vis et ecrous --Toumevis pour visa tete fendue Partie 1: Extremites de tournevis a main et a machine Reference number 1SO 2380-1:2004(E) ISO2004 ISO 2380-1:2004(E) PDF disclaimer This PDF fle may contain embedded typefaces. in accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer perfonning the editing. In downlaading this file, parties accept therein the responsibilty of not infringing Adobe's licensing poficy. The isO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to'create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO mernber bodies, In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. @ISO2004 All rights reserved, Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfitm, without permission in writing from either isO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 , CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ISO2004-Allrights reserved punSH kgpa Netfo ISO 2380-1:2004(E) Foreword Iso (the International Organization for Standardization)is a worldwide federation ofnational standards bodies (ISo member bodies). The work of preparing International Standards is normally carried out through ISO non-governmental, in liaison with Iso, also take part in the work. Iso coliaborates closely with the InternationalElectrotechnicalCommission(iEC)onallmattersofelectrotechnicalstandardization International Standards are drafted in accordance with the rules given in the iSO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO2380-1waspreparedbyTechnical Committee1SO/TC29,Small tools,Subcommittee SC 10Assembly tools for screws and nuts,pliers and nippers. This third edition cancels and replaces the second edition (Is0 2380-1:1997), which has been technically revised. Iso 2380 consists of the following parts, under the general title Assembly tools for screws and nuts - Screwdrivers for slotted-head screws: Part1:Tipsforhand-andmachine-operated screwdrivers Part 2:General requirements,lengths of bladesandmarking ofhand-operated screwdrivers ii Not for Resale 1SO 2380-1:2004(E) INTERNATIONALSTANDARD Assemblytoolsforscrewsand nuts--Screwdrivers forsiotted-headscrews. Part 1: Tipsforhand-and machine-operated screwdrivers Scope 1 operated screwdrivers for slotted-head screws. It also gives the technical specifications and test conditions for the screw-drivers and, in the case of hand-operated screwdrivers, specifies the test torque which the blade-to- handleconnectionshallwithstand 2 Normativereferences The following referenced documents are indispensable for the application of th